Van Air Deliquescent & Absorbent Desiccant for Natural Gas and Compressed Air
Van Air Systems has been the leading manufacturer of deliquescent desiccant for nearly 75 years. With desiccant being manufactured in Lake City, PA; Van Air Systems is still producing the best chemical drying agent for our customers. We offer four cost-effective, dependable, energy-free deliquescent desiccants for a variety of drying applications. If you were/are using any other manufacturer’s desiccant, now is the time to introduce them Van Air Systems Deliquescent Desiccant.

Recently our industry has seen a change in deliquescent desiccant manufacturers. The second largest manufacturer has exited the market leaving their customers without a clear solution. Van Air Systems has been manufacturing equivalent desiccants for years, so you end users can make the switch with confidence. You will get the same great performance from Van Air Systems Deliquescent Desiccant.


Dessicant Equivalent Chart

Van Air SystemsVan Gas TechnologiesLubrizol
SPGasDry™ PeakRG
10BFGasDry™ MaxSG
10BFGasDry™ MaxHydro-Lith E
4UFGasDry™ UltimateXENTRITE

Van Air Absorbent Deliquescent Desiccants

buynow

Dry-O-Lite / GasDry Prime

Dry-o-Lite DesiccantsDry-O-Lite or GasDry Prime, the industry-leading deliquescent desiccant, is a chemical drying agent specifically formulated for Van Air single tower compressed air dryers and natural gas Pipeline Dryers. Dry-O-Lite is a dense hygroscopic tablet that absorbs water vapor from streams of compressed air or gas. The surface of the desiccant tablet dissolves slowly, forming a brine solution which drops from the surface. The tablet continuously dissolves, or deliquesces, until the desiccant is fully consumed.

All Van Air deliquescent desiccants, including Dry-O-Lite, are non-toxic and fully water soluble.

In a properly sized Freedom Dryer or Pipeline Dryer, Dry-O-Lite will establish a relative humidity of 55%, which equates to a dew point approximately 20°F lower than the temperature of the compressed air or gas at the inlet of the dryer.

Features & Benefits

  • No energy consumption
  • Prevents condensation
  • Can be used indoors or outdoors
  • Prevents wintertime air and gas line freeze-ups
  • Environmentally safe
  • Low cost of operation relative to refrigerated dryers and regenerative desiccant dryers
  • ¾” tablet
  • Little or no maintenance on drying equipment
  • Available in 50# bags, 50# pails, 506# steel drums and 2,000# bulk bags

Applications

  • Abrasive blasting
  • Portable air drying
  • Low pressure gases, e.g. digester gas and landfill gas
  • Remote outdoor locations without electricity
  • Fuel gas dehydration for natural gas
  • Ready-mix, asphalt, and concrete plants
  • Pulp and paper
  • Steel mills
  • Dirty environments or areas with electrical classification restrictions

SP / GasDry Peak

SP-bigSP or GasDry Peak is a leading deliquescent desiccant formulated primarily for the dehydration of natural gas for use in Van Air Pipeline Dryers when the gas temperature is below 90°F. SP is a dense hygroscopic tablet that absorbs water vapor. The surface of the desiccant tablet dissolves slowly, forming a brine solution which drops from the surface. The tablet continuously dissolves, or deliquesces, until the desiccant is fully consumed.

Van Air deliquescent desiccants, including SP, are non-toxic and fully water soluble.

In a properly sized Pipeline Dryer, SP will establish a relative humidity of 33%, which equates to a dew point approximately 30°F lower than the temperature of the gas at the inlet of the dryer.

Features and Benefits

  • Requires no energy or fuel
  • For operating temperatures 80°F and lower
  • Prevents condensation
  • Inhibits natural gas hydrate formation
  • Can be used indoors or outdoors
  • Prevents gas line freeze-ups
  • Environmentally safe
  • No BTEX emissions
  • Available in 45# pails, 50# bags and 400# steel drums

Applications

  • Drying high pressure, low temperature sales gas
  • Fuel gas dehydration
  • Instrument gas dehydration

10BF / GasDry Max

10-BF-big10BF / GasDry Max is the most effective deliquescent desiccant from Van Air Systems. Formulated primarily for the dehydration of natural gas and for use in Van Air Pipeline Dryers, 10BF is a dense hygroscopic tablet that absorbs water vapor. The surface of the desiccant tablet dissolves slowly, forming a brine solution which drops from the surface. The tablet continuously dissolve, or deliquesces, until the desiccant is fully consumed.

Van Air deliquescent desiccants, including 10BF, are non-toxic and fully water soluble.

In a properly sized Pipeline Dryer, 10BF will establish a relative humidity of 13%, which equates to a dew point depression of approximately 50-60°F.

Features and Benefits

  • Requires no energy or fuel
  • For operating temperatures 100°F and lower
  • Prevents condensation
  • Inhibits natural gas hydrate formation
  • Can be used indoors or outdoors
  • Prevents air or gas line freeze-ups
  • Environmentally safe
  • Replace TEG dehydrators
  • No BTEX emissions
  • 1″ diameter tablet
  • Little or no maintenance required for drying equipment
  • Available in 7# pails and 25# pails

Applications

  • Meeting pipeline moisture specifications
  • Fuel gas dehydration
  • Instrument gas dehydration
  • Lowering dew point of chilled biogas and landfill gas for siloxane mitigation
  • Remote outdoor locations without electricity
  • Environments with electrical classification restrictions

4UF / GasDry Ultimate

4UFGasDryUltimate
Natural gas or process gas dehydration at low pressures, low flow rates, and / or low temperatures can be very difficult. For these unique applications, Gas DryTM Ultimate/4UF was developed to meet low dew point requirements when other desiccants or glycols are ineffective.

Features and Benefits

  • 7 lbs H2O/MMSCF gas is attainable @ 50 psig & 60°F
  • 20 lbs H2O/MMSCF gas is attainable @ 25 psig & 80°F
  • Gas temperatures below freezing can be dried and still
  • obtain a low equilibrium RH

  • 4% equilibrium RH
  • Can dry gas for lower cost than glycol systems, in some applications

Applications

  • Meeting pipeline moisture specifications
  • Fuel gas dehydration
  • Instrument gas dehydration
  • Lowering dew point of chilled biogas and landfill gas for siloxane mitigation
  • Remote outdoor locations without electricity
  • Environments with electrical classification restrictions

Van Air Adsorbent Regenerative Desiccants

buynow

Activated Alumina

activated-alumina-fullActivated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying.

In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design.

In compressed air desiccant dryers, a 1/8″ (2-5 mm) activated alumina bead is most commonly used. The ¼” (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16″ (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8″ and ¼” material.

Features and Benefits of Activated Alumina Desiccant

  • High adsorption capacity for reducing initial cost, energy consumption, and operating costs
  • Low abrasion for ensuring minimal dusting and a low pressure drop
  • Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration.
  • High crush strength for limiting dusting during loading of desiccant into dryer towers
  • Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed
  • In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years
  • Available in 25# pails, 50# bags, 375# steel drums and 2,000# bulk bags

Molecular Sieve

desiccant_molecular_sieve_largeMolecular sieve is highly porous sodium aluminosilicate bead for the adsorption of a wide range of liquids and gases. It has a fixed pore size according to the material specification. Van Air Systems offers molecular sieve with a 4 angstrom pore size. Because of its high comparative cost, molecular sieve is normally used for special process applications. In compressed air and gas drying applications, molecular sieve will deliver pressure dew point to -100°F, depending on dryer design and operating conditions.

Features and Benefits

  • More consistent moisture retention from 10% to 100% relative humidity
  • Used to produce dew points as low as -100°F.
  • With a round shape, Van Air molecular sieve has a higher abrasion resistance and delivers a lower pressure drop that extruded molecular sieves.
  • Available in 5# pails, 25# pails, 50# bags and 300# steel drums

Silica Gel

desiccant_silica_gel_largeSilica gel is a spherical bead consisting of 97% silica and 3% alumina with a highly porous surface and a strong affinity for adsorbing water. Silica gel is also applied as a selective adsorbent for a wide-range of hydrocarbons, C02, siloxanes, sulfur, and many other compounds.

Because silica gel fractures in the presence of liquid water, it is often protected with a pre-bed of activated alumina.

In air and gas drying applications, dew points of -40°F and lower can be achieved with silica gel.

Features and Benefits

  • High moisture retention capacity under dynamic conditions, allowing heated desiccant dryers with a higher design capacity and lower regeneration temperature
  • A uniform bead shape provides for a lower pressure drop and less abrasion than granular types of silica gel.
  • Available in two types, non-indicating and indicating. Indicating silica gel is impregnated with a moisture indicator that changes color from blue to pink when saturated.
  • High static adsorption (moisture retention) under certain relative humidity conditions
  • Available in indicating (blue to pink) and non-indicating
  • Available in 5# pails, 25# pails, 50# bags and 330# steel drums

AVP also supplies Genuine Van Gas Technologies GasDry Prime, GasDry Peak, and GasDry Max that are formulated specifically for natural gas dryers and dehydration systems.

I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.